Add mtgbox + ring light 2

mtgbox.scad

@@ -0,0 +1,83 @@
+render_box=true;
+render_divider=false;
+render_lid=false;
+
+mtg_deck_height = 3 * 25.4; // 3", sleeved, card + paper proxy
+hollow_w = 95; // cards are 92 in sleeves
+hollow_h = 70; // cards are 62 in sleeves
+
+n_decks = 3;
+wall_thickness = 5;
+divider_depth = 2;
+divider_epsilon = 1;
+
+module divider() {
+   cube([hollow_w + 2*divider_epsilon, divider_depth, hollow_h+wall_thickness]);
+}
+
+module magnet() {
+   cylinder(h=1, d=3, $fn=100);
+}
+
+module box_magnets() {
+  translate([outer_w-3,3,outer_h-1+0.0001]) {
+     #magnet();
+  }
+  translate([outer_w-3,outer_d-3,outer_h-1+0.0001]) {
+     #magnet();
+  }
+  translate([3,3,outer_h-1+0.0001]) {
+     #magnet();
+  }
+  translate([3,outer_d-3,outer_h-1+0.0001]) {
+     #magnet();
+  }  
+}
+internal_space_w = hollow_w;
+internal_space_depth = mtg_deck_height * n_decks;
+if (n_decks > 1) {
+    internal_space_depth = internal_space_depth + divider_depth * (n_decks-1);
+}
+internal_space_height = hollow_h;
+
+outer_w = internal_space_w + 2*wall_thickness;
+outer_d = internal_space_depth + 2*wall_thickness;
+outer_h = internal_space_height + 2*wall_thickness;
+
+dividers = n_decks - 1;
+
+module box() {
+difference() {
+  cube([outer_w, outer_d, outer_h]);
+  translate([wall_thickness, wall_thickness, wall_thickness]) {
+    cube([internal_space_w, internal_space_depth, internal_space_height+wall_thickness+.01]);
+  };
+  for(div_n = [1 : dividers]) {
+    translate([wall_thickness - divider_epsilon, wall_thickness +div_n*mtg_deck_height + divider_depth/2, wall_thickness]) {
+      #divider();
+    };
+  }
+  box_magnets();
+};
+}
+
+module lid() {
+  difference() {
+    cube([outer_w, outer_d, wall_thickness]);  
+    translate([0, 0, -outer_h+wall_thickness]) {
+      box_magnets();
+    };
+  }
+}
+
+if (render_box) {
+  box();
+}
+
+if (render_lid) {
+  lid();
+}
+
+if (render_divider) {
+  divider();
+}

ring light part 2.scad

@@ -0,0 +1,38 @@
+// 92x59 hole mm
+// 10mm border
+// 4" under table maybe? 100mm ish, w/ 4 screw holes
+// maybe like 25mm thick?
+
+hole_w = 92;
+hole_l = 59;
+trim_w = 10;
+undertable_l = 100;
+depth = 30;
+
+width = hole_w + 2 * trim_w;
+length = undertable_l + trim_w * 2 + hole_l;
+
+screw_inset = 20;
+// #8 2" screw
+screw_hole_diameter = 3.45;
+#difference() {
+  cube([width, length, depth]);
+  translate([trim_w, trim_w, 0]) {
+    cube([hole_w, hole_l, depth]);  
+  };
+  
+
+  translate([width-screw_inset,length-screw_inset,0]) {
+  cylinder(depth*2, d = screw_hole_diameter, center=true, $fn=100);  
+  };
+  translate([screw_inset,length-screw_inset,0]) {
+  cylinder(depth*2, d = screw_hole_diameter, center=true, $fn=100);  
+  };
+  translate([width-screw_inset,2*trim_w+hole_l+screw_inset,0]) {
+  cylinder(depth*2, d = screw_hole_diameter, center=true, $fn=100);  
+  };
+  translate([screw_inset,2*trim_w+hole_l+screw_inset,0]) {
+  cylinder(depth*2, d = screw_hole_diameter, center=true, $fn=100);  
+  };
+};
+